Your browser does not support the NLM PubReader view.

Go to this page to see a list of supporting browsers.

Nalco 9916 Msds __hot__ Info

Typically classified as hazardous due to its corrosive nature or skin/eye irritation potential.

According to OSHA’s Hazard Communication Rule (29 CFR 1910.1200) and international GHS frameworks, Nalco 9916 presents specific operational hazards that must be monitored:

Health & safety (general precautions—use SDS as definitive source) Nalco 9916 Msds

The most critical section of the Nalco 9916 MSDS is the Hazard Identification. Under modern GHS standards, this document classifies the substance with specific signal words and pictograms. For a product like Nalco 9916, the MSDS typically highlights severe hazards. It is generally classified as corrosive, capable of causing severe skin burns and eye damage. Furthermore, it often carries hazard statements regarding acute toxicity if inhaled or ingested, and importantly, it is labeled as very toxic to aquatic life. This section of the MSDS transforms the chemical from a generic "water treatment solution" into a substance that demands respect, signaling to the worker that standard personal protective equipment (PPE) is not just recommended, but mandatory.

Do you need help with for handling this product, org., outdoor vs. indoor storage)? Let me know so I can provide more targeted information. Share public link Typically classified as hazardous due to its corrosive

To ensure you get the exact information you need, could you clarify a few details?

: Wash the affected area thoroughly with soap and water. Remove any contaminated clothing. For a product like Nalco 9916, the MSDS

Prolonged contact can cause drying and irritation (dermatitis).

According to the data sheet, Nalco 9916 typically carries specific signal words and pictograms.

Safe deployment of Nalco 9916 relies on controlled environments and proper industrial hygiene practices. Storage Protocols

is a high-molecular-weight, cationic water-soluble polymer powder manufactured by Nalco Water, an Ecolab company, designed for heavy-duty industrial coagulation and flocculation processes. Understanding its Safety Data Sheet (SDS), formerly referred to as the Material Safety Data Sheet (MSDS), is essential for workplace safety, regulatory compliance, and proper environmental handling.

Fig. 1.

Fig. 1.

Groove configuration of the dissimilar metal joint between HMn steel and STS 316L

Fig. 2.

Fig. 2.

Location of test specimens

Fig. 3.

Fig. 3.

Dissimilar metal joints for welding deformation measurement: (a) before welding, (b) after welding

Fig. 4.

Fig. 4.

Stress-strain curves of the DMWs using various welding fillers

Fig. 5.

Fig. 5.

Hardness profiles for various locations in the DMWs: (a) cap region, (b) root region

Fig. 6.

Fig. 6.

Transverse-weld specimens of DN fractured after bending test

Fig. 7.

Fig. 7.

Angular deformation for the DMW: (a) extracted section profile before welding, (b) extracted section profile after welding.

Fig. 8.

Fig. 8.

Microstructure of the fusion zone for various DSWs: (a) DM, (b) DS, (c) DN

Fig. 9.

Fig. 9.

Microstructure of the specimen DM for various locations in HAZ: (a) macro-view of the DMW, (b) near fusion line at the cap region of STS 316L side, (c) near fusion line at the root region of STS 316L side, (d) base metal of STS 316L, (e) near fusion line at the cap region of HMn side, (f) near fusion line at the root region of HMn side, (g) base metal of HMn steel

Fig. 10.

Fig. 10.

Phase analysis (IPF and phase map) near the fusion line of various DMWs: (a) location for EBSD examination, (b) color index of phase for Fig. 10c, (c) phase analysis for each location; ① DM: Weld–HAZ of HMn side, ② DM: Weld–HAZ of STS 316L side, ③ DS: Weld–HAZ of HMn side, ④ DS: Weld–HAZ of STS 316L side, ⑤ DN: Weld–HAZ of HMn side, ⑥ DN: Weld–HAZ of STS 316L side, (the red and white lines denote the fusion line) (d) phase fraction of Fig. 10c, (e) phase index for location ⑤ (Fig. 10c) to confirm the formation of hexagonal Fe3C, (f) phase index for location ⑤ (Fig. 10c) to confirm no formation of ε–martensite

Fig. 11.

Fig. 11.

Microstructural prediction of dissimilar welds for various welding fillers [34]

Fig. 12.

Fig. 12.

Fractured surface of the specimen DN after the bending test: (a) fractured surface (x300), (b) enlarged fractured surface (x1500) at the red-square location in Fig. 12a, (c) EDS analysis of Nb precipitates at the red arrows in Fig. 12b, (d) the cross-section(x5000) of DN root weld, (e) EDS analysis in the locations ¨ç–¨é in Fig. 12d

Fig. 13.

Fig. 13.

Mapping of Nb solutes in the specimen DN: (a) macro view of the transverse DN, (b) Nb distribution at cap weld depicted in Fig. 12a, (c) Nb distribution at root weld depicted in Fig. 12a

Table 1.

Chemical composition of base materials (wt. %)

C Si Mn Ni Cr Mo
HMn steel 0.42 0.26 24.2 0.33 3.61 0.006
STS 316L 0.012 0.49 0.84 10.1 16.1 2.09

Table 2.

Chemical composition of filler metals (wt. %)

AWS Class No. C Si Mn Nb Ni Cr Mo Fe
ERFeMn-C(HMn steel) 0.39 0.42 22.71 - 2.49 2.94 1.51 Bal.
ER309LMo(STS 309LMo) 0.02 0.42 1.70 - 13.7 23.3 2.1 Bal.
ERNiCrMo-3(Inconel 625) 0.01 0.021 0.01 3.39 64.73 22.45 8.37 0.33

Table 3.

Welding parameters for dissimilar metal welding

DMWs Filler Metal Area Max. Inter-pass Temp. (°C) Current (A) Voltage (V) Travel Speed (cm/min.) Heat Input (kJ/mm)
DM HMn steel Root 48 67 8.9 2.4 1.49
Fill 115 132–202 9.3–14.0 9.4–18.0 0.72–1.70
Cap 92 180–181 13.0 8.8–11.5 1.23–1.59
DS STS 309LMo Root 39 68 8.6 2.5 1.38
Fill 120 130–205 9.1–13.5 8.4–15.0 0.76–1.89
Cap 84 180–181 12.0–13.5 9.5–12.2 1.06–1.36
DN Inconel 625 Root 20 77 8.8 2.9 1.41
Fill 146 131–201 9.0–12.0 9.2–15.6 0.74–1.52
Cap 86 180 10.5–11.0 10.4–10.7 1.06–1.13

Table 4.

Tensile properties of transverse and all-weld specimens using various welding fillers

ID Transverse tensile test
 All-weld tensile test
TS (MPa) YS (Ϯ1) (MPa) TS (MPa) YS (Ϯ1) (MPa) EL (Ϯ2) (%)
DM 636 433 771 540 49
DS 644 433 676 550 42
DN 629 402 785 543 43

(Ϯ1) Yield strength was measured by 0.2% offset method.

(Ϯ2) Fracture elongation.

Table 5.

CVN impact properties for DMWs using various welding fillers

DMWs Absorbed energy (Joule)
 Lateral expansion (mm)
1 2 3 Ave. 1 2 3 Ave.
DM 61 60 53 58 1.00 1.04 1.00 1.01
DS 45 56 57 53 0.72 0.81 0.87 0.80
DN 93 95 87 92 1.98 1.70 1.46 1.71

Table 6.

Angular deformation for various specimens and locations

DMWs Deformation ratio (%)
Face Root Ave.
DM 9.3 9.4 9.3
DS 8.2 8.3 8.3
DN 6.4 6.4 6.4

Table 7.

Typical coefficient of thermal expansion [26,27]

Fillers Range (°C) CTE (10-6/°C)
HMn 25‒1000 22.7
STS 309LMo 20‒966 19.5
Inconel 625 20‒1000 17.4